A Step-by-Step Overview to Setting Up a Bathtub
A Step-by-Step Overview to Setting Up a Bathtub
Blog Article
How do you actually feel when it comes to How to Install a Bathtub?
Mounting a bathtub isn't specifically rocket science, but it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a new one is likewise a reasonably difficult job. If the old tub is easily obtainable, the project can relocate speedily; if you have to open up a wall surface to remove the old bathtub and also position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will require a helper to leave the old tub as well as embeded in the new one. Make certain you have qualified on your own for the job as well as fit attempting it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Chances are you might require a professional plumber to make tube links.
This write-up will assist you mount a new bathtub in your shower room if you have actually already purchased a brand-new bathtub and don't require to change the setup of your previous water supply pipes.
Your tools as well as product list need to comprise the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of eliminating the existing taps can be quite problematic due to the restricted access that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the installing hole in the bath/basin making certain that the washers are in area between the tap and also the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The former type needs to be linked to the tap ends first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Bath tub
Using both wooden boards under its feet, position the tub in the called for position. The wood boards are valuable in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to make certain that the tub is leveled all round. This can be achieved by inspecting the spirit level and also changing the feet on the bath tub up until the spirit level checks out level.
To mount taps, fit all-time low of the furthest adaptable tap port to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water and examine all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and likewise examine the overflow outlet as well as the regular outlet for leaks.
Ultimately, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the bath tub ought to wait up until the bathtub has been made use of at least when as this will certainly settle it right into its last position.
Planning for the Installation
First of all, the sustaining frame provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the faucet features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to stop strain on the bathtub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last setting.
Tiling Around the Tub
In the area where the bath meets the tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to crack a rigid seal, creating the water to pass through the wall surface between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your components and also installations. They are marketed in tubes and cartridges, and can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked newspaper or soft rope. Remember to constantly fill up the bathtub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can split fairly very early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that article about Tools You Need to Install a New Bathtub through someone on our other web address. Do you know somebody else who is curious about the subject? Take a moment to promote it. Thanks for going through it.
Automated Marketing
Report this page